Arch radius & curved wall stud calculator
Calculate true circle radius, curved soffit arc length, central angle and symmetric cripple stud cut lengths from arch width and rise.
The calculation models a true circular segment where the rise is at most half the chord width (a full semicircle). Elliptical, Tudor or three-centered arches have multiple radii and require separate layout coordinates. Deduct the thickness of your flexible plywood or drywall soffit strip and header plate before cutting framing cripples.
To lay out a circular arched doorway or cased opening from its clear width (chord W) and center rise (sagitta H), calculate the true circle radius R = (W² ÷ (8 × H)) + (H ÷ 2). Enter your arch width and rise above to get the true radius in feet and 1/16 in fractions, the curved soffit strip length, the central angle and the symmetric cripple stud cut lengths at each on-center station.
How to calculate arch radius from width (chord) and rise
When framing a segmental arched doorway, cased opening or barrel ceiling, the blueprint usually gives only two dimensions: the clear horizontal opening width (the chord, W) and the vertical height from the spring line to the top of the arch at the center (the rise or sagitta, H). To swing a smooth circular curve with a trammel beam or tape measure, you need the true radius R of the circle that passes through both jambs and the crown.
Circle Radius (R) = (W² ÷ (8 × H)) + (H ÷ 2) Central Angle (θ rad) = 2 × asin( (W ÷ 2) ÷ R ) Curved Arc Length = R × θ (with θ in radians) Cripple drop at offset x = R − √(R² − x²) (measured down from crown level)
The formula comes directly from applying the Pythagorean theorem to the right triangle formed by the circle's center, the jamb spring point and the midpoint of the chord: R² = (W ÷ 2)² + (R − H)². For a 6 ft (72 in) wide opening with an 18 in rise, the radius is (72² ÷ (8 × 18)) + (18 ÷ 2) = 36 + 9 = 45 in (3′ 9″), and the curved soffit strip along the arch is 6′ 11 7/16″ (83.46 in) long.
Arch radius and curved soffit length for common doorway spans
A flatter arch (small rise across a wide opening) produces a much longer radius than a deep arch. When the rise equals exactly half the opening width (for example, a 36 in rise on a 72 in wide opening), the arch is a full 180° semicircle and the radius is simply half the width. The table below lists the true radius, curved soffit length and central angle for common residential openings.
| Opening width (chord) | Arch rise (sagitta) | True circle radius | Curved soffit arc length | Central angle |
|---|---|---|---|---|
| 3′ 0″ | 6″ | 2′ 6″ (30.0″) | 3′ 2 5/8″ (38.6″) | 73.7° |
| 3′ 0″ | 12″ | 1′ 7 1/2″ (19.5″) | 3′ 9 7/8″ (45.9″) | 134.8° |
| 4′ 0″ | 8″ | 3′ 4″ (40.0″) | 4′ 3 1/2″ (51.5″) | 73.7° |
| 4′ 0″ | 12″ | 2′ 6″ (30.0″) | 4′ 7 5/8″ (55.6″) | 106.3° |
| 5′ 0″ | 10″ | 4′ 2″ (50.0″) | 5′ 4 3/8″ (64.4″) | 73.7° |
| 5′ 0″ | 15″ | 3′ 1 1/2″ (37.5″) | 5′ 9 9/16″ (69.5″) | 106.3° |
| 6′ 0″ | 12″ | 5′ 0″ (60.0″) | 6′ 5 1/4″ (77.2″) | 73.7° |
| 6′ 0″ | 18″ | 3′ 9″ (45.0″) | 6′ 11 7/16″ (83.5″) | 106.3° |
| 8′ 0″ | 16″ | 6′ 8″ (80.0″) | 8′ 6 15/16″ (103.0″) | 73.7° |
| 8′ 0″ | 24″ | 5′ 0″ (60.0″) | 9′ 3 1/4″ (111.3″) | 106.3° |
Use the curved soffit arc length column to order and cut your bending plywood, kerfed MDF or flexible drywall strip that wraps the underside of the arch.
Worked example: cripple stud cut lengths for a 6 ft arched opening
To frame a segmental arch inside a rectangular rough opening, carpenters often sheathe both faces with 1/2 in or 3/4 in plywood cut to the radius, or install pairs of vertical cripple studs spaced evenly outward from the centerline of the arch down from the flat header to the curve. For a 6 ft (72 in) wide arch with an 18 in rise (45 in radius) at 12 in on center from the centerline:
| Station from arch center | Drop below crown (1/16″) | Exact decimal inches |
|---|---|---|
| Pair 1 (±12″ from center) | 1 5/8″ | 1.63 in |
| Pair 2 (±24″ from center) | 6 15/16″ | 6.93 in |
| Pair 3 (±36″ from center) | 18″ | 18.00 in |
At the dead center of the opening (offset 0), the arch touches the crown level (0 in drop, plus whatever minimum collar thickness you leave above the crown before the header). At ±12 in from center, the curve drops 1 5/8″; at ±24 in it drops 6 15/16″; and at ±36 in (the jamb spring line) it drops the full 18″ rise.
How to draw a large-radius arch when the pivot is below the floor
On a gentle arch—such as an 8 ft wide opening with a 12 in rise, where the radius is 8 ft 6 in (102 in)—the pivot point sits 7 ft 6 in below the crown. If the opening is framed in place, that pivot point falls below the subfloor where you cannot drive a nail for a string trammel. You have two clean field methods:
- Scribe the plywood on the subfloor first: lay your 4×8 plywood sheet flat on the subfloor, snap a baseline representing the chord, measure down
R − H(90 in on the 8 ft × 12 in arch) onto the open floor to set your pivot screw, and swing a rigid 1×2 wood trammel stick across the plywood. - Plot the calculated ordinate drops directly on the wall: set the calculator above to a 6 in spacing, mark every 6 in horizontally from the centerline along the header, transfer the calculated vertical drops downward at each station, and bend a thin 1/4 in wood batten or PVC trim strip through the marks to fairing-scribe a smooth curve in place.
To check that your rough jambs and header are square before installing the arch plates, use the right triangle and 3-4-5 calculator.
Frequently asked questions
How do you find the radius of an arch from width and height?
Square the arch width (chord), divide by 8 times the arch rise (height), and add half the rise: R = (W² ÷ (8 × H)) + (H ÷ 2). Keep width and rise in the same unit, such as inches.
How long is the curved soffit strip inside an arch?
Convert the central angle θ = 2 × asin((W ÷ 2) ÷ R) to radians and multiply by the radius R. The calculator reports this as the Curved soffit arc length in feet, inches and 1/16 in fractions.
What is the spring line of an arch?
The spring line is the horizontal line across the opening where the vertical jambs end and the curve of the arch begins to rise. The arch rise (sagitta) is measured vertically from the center of the spring line up to the underside of the crown.
How do I bend drywall around an arched doorway?
For gentle radii over 36 inches, lightly mist the back paper of 1/4 in or 1/2 in drywall or score the back at 1 to 2 inch intervals and press it gently against closely spaced 2×4 blocking around the curve. For tight semicircle arches, layer two sheets of 1/4 in flexible drywall over a curved plywood sub-strip.
Why does the calculator say the rise cannot exceed half the arch width?
When the rise equals half the width (for example, an 18 in rise on a 36 in wide doorway), the arc is a full 180° semicircle with radius R = W ÷ 2. An arch taller than a semicircle is either a stilted arch (vertical jamb extensions below a semicircle) or a pointed Gothic/elliptical arch with two centers.