Stairs & Framing

Crown Molding Angle Calculator: Miter & Bevel Settings

Free crown molding angle calculator. Get exact miter and bevel saw angles for 38°/52° and 45°/45° crown laid flat or nested on 90°, 135° and out-of-square corners.

Free online tool

Crown molding miter & bevel calculator

Find exact compound miter saw settings for cutting crown molding laid flat on the saw table, or nested upside-down against the fence.

Compound saw settings (crown laid flat)

31.62° miter · 33.86° bevel

Saw table miter angle
31.62° (laid flat on saw table)
Saw blade bevel tilt
33.86° blade tilt
Nested cut (against fence)
45° miter with 0° bevel (nested upside-down against fence)
Molding & corner
38°/52° crown on a 90° corner

Miter = atan(sin(38°) ÷ tan(45°)) = 31.619°. Bevel = asin(cos(38°) × cos(45°)) = 33.863°.

Angles are for equal-spring crown molding meeting at the entered wall corner on a level ceiling. When cutting crown laid flat on a compound miter saw, keep the bottom (wall) edge of the molding tight against the fence for standard orientation and test-fit two short scrap blocks on the actual wall corner before cutting full-length trim.

Cutting crown molding laid flat on a compound miter saw combines a table miter rotation with a blade bevel tilt that depend on both the wall corner angle and the molding’s spring angle (38°/52° or 45°/45°). Enter your measured wall corner and spring angle above to get the exact compound miter and bevel settings—or the nested miter angle—for 90°, 135° bullnose and out-of-square drywall corners.

Compound miter and bevel formulas for crown laid flat

Crown molding bridges the wall and the ceiling at a tilt called the spring angle—the angle between the back of the molding and the vertical wall. When you lay the molding flat on a compound miter saw table instead of propping it upside-down against the fence, the single corner angle splits into two simultaneous compound rotations: a horizontal table miter angle and a tilted blade bevel angle.

Saw Miter Angle = atan( sin(spring angle) ÷ tan(wall corner ÷ 2) )
Saw Bevel Angle = asin( cos(spring angle) × cos(wall corner ÷ 2) )
Nested Miter    = |180° − wall corner| ÷ 2   (with 0° bevel, molding propped at spring angle)

On a true 90° wall corner, standard 38°/52° crown (38° against the wall, 52° against the ceiling) requires a 31.62° miter and a 33.86° bevel—the two factory detent stops stamped at 31.6° and 33.9° on compound miter saws. Traditional 45°/45° crown on a 90° corner requires a 35.26° miter and a 30.00° bevel.

Crown molding miter and bevel chart (85° to 95° and 135° corners)

Drywall corners are rarely an exact 90°. Joint compound buildup on outside corner bead often pushes a corner down to 87° or 88°, while inside taped corners frequently measure 91° or 92°. Cutting standard 90° detent settings on an 88° outside corner leaves an open 1/16 in gap at the face. Measure the true wall corner with a digital protractor, divide or enter the full angle above, or read the exact saw settings from the chart below.

Compound miter and bevel angles for 38°/52° and 45°/45° crown laid flat, plus nested miter
Measured wall corner38° spring Miter38° spring Bevel45° spring Miter45° spring BevelNested Miter (0° bevel)
85°33.90°35.52°37.66°31.42°47.50°
86°33.43°35.19°37.17°31.14°47.00°
87°32.97°34.86°36.69°30.86°46.50°
88°32.52°34.53°36.21°30.57°46.00°
89°32.07°34.20°35.74°30.29°45.50°
90° (square)31.62°33.86°35.26°30.00°45.00°
91°31.17°33.53°34.79°29.71°44.50°
92°30.73°33.19°34.33°29.42°44.00°
93°30.30°32.85°33.86°29.13°43.50°
94°29.86°32.51°33.40°28.83°43.00°
95°29.43°32.17°32.94°28.54°42.50°
120°19.57°23.20°22.21°20.70°30.00°
135° (bullnose / bay)14.31°17.55°16.32°15.70°22.50°
150°9.37°11.77°10.73°10.55°15.00°

For a 135° bullnose drywall corner or bay window angle with 38°/52° crown laid flat, set the saw table to 14.31° miter and tilt the blade to 17.55° bevel.

Cutting crown flat on the table versus nested upside-down

Finish carpenters use two distinct setups at the miter saw, and each has a specific advantage depending on the molding width and the saw capacity:

  • Laid flat (compound cut): the back of the molding rests flat on the saw base with the bottom (wall) edge pushed tight against the fence. Wide 5 1/4 in to 7 1/4 in crown moldings that would exceed the vertical cutting height of a 10 in saw blade when stood up can be cut easily lying flat on a sliding compound miter saw, and the workpiece cannot slip down the fence mid-cut.
  • Nested (upside-down against the fence): the molding sits upside-down at the exact angle it will hang on the wall, with its ceiling edge resting on the saw table and its wall edge high against the vertical fence (held in place by crown stops or a sacrificial fence strip). Because the saw table acts as the ceiling, the blade stays at 0° bevel and you swing only the miter table to (180° − corner) ÷ 2 (45° for a 90° corner).

Fence and blade orientation for inside and outside corners

When cutting crown molding laid flat with a left-tilting single-bevel saw (keep the bottom wall edge of the molding against the fence for all four cuts):

  1. Inside corner, left piece: swing miter table Right to the miter angle; tilt bevel Left; keep the left side of the blade.
  2. Inside corner, right piece: swing miter table Left to the miter angle; keep bevel tilted Left; keep the right side of the blade.
  3. Outside corner, left piece: swing miter table Left to the miter angle; keep bevel tilted Left; keep the left side of the blade.
  4. Outside corner, right piece: swing miter table Right to the miter angle; keep bevel tilted Left; keep the right side of the blade.

Always cut two 12-inch test blocks first and hold them against the wall corner before cutting a 16-foot stick of trim. To split a long wall run or space decorative ceiling beams evenly, use the divide feet and inches calculator.

Frequently asked questions

What are the miter and bevel angles for crown molding on a 90 degree corner?

For standard 38°/52° crown molding laid flat on the saw table, set the miter to 31.62° (31.6° detent) and the bevel to 33.86° (33.9° detent). For 45°/45° crown laid flat, set the miter to 35.26° (35.3° detent) and the bevel to 30.00°.

How do I tell if my crown molding is 38/52 or 45/45?

Hold a short piece against a square 90° framing square so both back flats touch the legs of the square. If the bottom and top edges sit at the same distance from the corner (an isosceles triangle), it is 45°/45° crown. If the molding projects further across the ceiling than it drops down the wall, it is 38°/52° crown (38° wall spring angle, 52° ceiling angle).

What angles do I cut crown molding for a 135 degree bullnose or bay window corner?

For 38°/52° crown laid flat on a 135° corner, set the miter angle to 14.31° and the bevel angle to 17.55°. If cutting nested upside-down against the fence, set the bevel to 0° and the miter to 22.5°.

Why is there a gap at the bottom or top of my crown molding joint?

Either the wall corner is not 90° (measure it with an angle finder and enter the exact degree above; an 88° corner needs a 32.51° miter and 34.81° bevel on 38° crown), or the ceiling is not level with the wall, or the back of the molding was rocked slightly off the saw table during the cut.

Should I cope or miter inside crown molding corners?

Many trim carpenters cope inside corners on stain-grade or wood crown because a coped joint stays visually closed if the house framing shrinks seasonally. On MDF or painted polyurethane crown glued with cyanoacrylate adhesive, a precise compound miter matched to the measured corner angle installs quickly and cleanly.

How these guides are prepared · Calculations and table values come from the same code as the free tools and are checked by automated tests and against the formulas in the Construction Pro app. Code references are for orientation: confirm requirements with your jurisdiction and your project documents. Found an error? Tell the developer.
Take the next job with you

Keep the calculation with the project.

Use feet-inch fractions, specialty trade tools and saved job calculations in Construction Pro for iPhone and iPad. Free download with in-app Pro options.

View on the App Store ↗

Keep working

Browse all guides