Materials & Takeoff

Deck Board Calculator: 5/4×6 Rows, Linear Feet & Screws

Free deck board calculator. Enter deck dimensions, actual board width and gap spacing to get board rows across, 12 or 16 ft boards to order, joists and screw counts.

Free online tool

Deck board, joist & screw calculator

Calculate rows of deck boards across a deck, total stock boards to buy, framing joists and fastener counts.

Deck boards to order

29 boards (16 ft stock)

Board rows across deck
26 rows across 12′ 0″ (5 5/8″ per row module)
Total linear decking
457.6 linear ft with 10% waste (416 ft net)
Framing joists (1 run)
13 joists at 16″ O.C. across 16′ 0″
Fasteners (2 per crossing)
~744 screws/fasteners (2 per board at each joist + 10%)

Rows = ⌈144 in ÷ (5.5 + 0.125) in⌉ = 26. Linear ft = 26 × 16 ft × 1.1 = 457.6 ft, or 29 boards of 16 ft.

Always enter the actual surfaced width of the board (5½ in for a nominal 6 in board), not 6 in. Dividing deck square footage by 0.5 ft under-counts by nearly 7%. Joist count is for a single straight span without double rim joists, beam cantilevers, picture-frame borders or stair stringers; add extra boards and framing for borders and diagonal layouts.

Nominal 6-inch deck boards (5/4×6 wood, 2×6 lumber and standard composite planks) have an actual surfaced width of 5 1/2 inches, not 6 inches. With a 1/8 inch drainage gap, each row covers 5 5/8 inches, requiring 213.3 linear feet of decking per 100 square feet—nearly 7% more than a 6-inch division predicts. Enter your deck dimensions, board width and gap above to calculate board rows, stock boards, joists and screws.

Why dividing deck area by 6 inches leaves you short on boards

The most frequent mistake on a deck lumber order is treating a nominal 6-inch deck board (5/4×6 radius-edge decking, 2×6 framing lumber or standard grooved compositeplank) as if it covered 6 inches (0.5 ft) of width. In reality, a nominal 6-inch board is surfaced to an actual width of 5 1/2 inches. Even with a 1/8 in drainage gap between rows, each course advances only 5 5/8 inches (5.625 in) across the joists.

Row module (in)         = Actual board width (in) + Gap between boards (in)
Rows across deck width  = ⌈Deck width (in) ÷ Row module (in)⌉
Total linear decking    = Rows × Deck length (ft) × (1 + waste %)
Stock boards to order   = ⌈Total linear decking (ft) ÷ Stock board length (ft)⌉

If you divide a 16 ft × 12 ft (192 sq ft) deck by 0.5 ft per board, you estimate 384 linear feet (24 sixteen-foot boards). Using the true 5 1/2 in board width plus a 1/8 in gap, a 12 ft (144 in) deck width actually requires ⌈144 ÷ 5.625⌉ = 26 rows, which is 416 net linear feet (26 boards before waste, or 29 boards with 10% waste)—two full boards more than the nominal shortcut before a single scrap is cut.

5/4×6 deck boards, joists and screws for common deck sizes

Counts below use 5 1/2 in actual width boards with a 1/8 in gap, joists at 16 in on center, 2 screws per board at every joist crossing and a 10% waste allowance.

Deck boards (5½ in actual width), joists and screws for common deck sizes
Deck size (area)Board rows acrossLinear ft (with 10% waste)Stock boards to orderJoists (16″ O.C.)Deck screws
10′ × 10′ (100 sq ft)22 rows242 lin ft21 × 12′ boards9 joists~436 screws
12′ × 12′ (144 sq ft)26 rows343 lin ft29 × 12′ boards10 joists~572 screws
16′ × 12′ (192 sq ft)26 rows458 lin ft29 × 16′ boards13 joists~744 screws
20′ × 12′ (240 sq ft)26 rows572 lin ft29 × 20′ boards16 joists~916 screws
20′ × 16′ (320 sq ft)35 rows770 lin ft39 × 20′ boards16 joists~1232 screws
24′ × 16′ (384 sq ft)35 rows924 lin ft77 × 12′ boards19 joists~1463 screws

When choosing stock board lengths, pick a length that spans the full deck or breaks cleanly on the center of a 1 1/2 in joist. A 16 ft deck covered with 16 ft boards has zero butt joints in the field; a 24 ft wide deck works best with alternating 16 ft and 8 ft boards (or two 12 ft boards with a solid double-joist parting board down the middle so two cut ends never share a single 1 1/2 in joist thickness).

Linear feet of decking per 100 sq ft by board width and gap

When comparing quotes between narrow 2×4 redwood, standard 5/4×6 cedar or composite, and wide 2×8 planks, use the coverage multiplier per 100 sq ft of deck surface:

Net linear feet of decking needed per 100 sq ft of deck area (before waste)
Actual board widthGap spacingRow moduleNet linear ft per 100 sq ft
3 1/2 in (nominal 4″)1/8 in3 5/8 in (3.625″)331.0 lin ft
5 1/2 in (nominal 6″)0 in (tight wet PT)5 1/2 in (5.500″)218.2 lin ft
5 1/2 in (nominal 6″)1/8 in (standard wood)5 5/8 in (5.625″)213.3 lin ft
5 1/2 in (nominal 6″)3/16 in (composite clip)5 11/16 in (5.6875″)211.0 lin ft
5 1/2 in (nominal 6″)1/4 in (wide drainage)5 3/4 in (5.750″)208.7 lin ft
7 1/4 in (nominal 8″)1/8 in7 3/8 in (7.375″)162.7 lin ft

Wet pressure-treated southern pine shrinks across its grain as it dries in the sun and is often laid tight (0 in gap), requiring 218.2 linear feet per 100 sq ft. Kiln-dried cedar, hardwoods (Ipe, Cumaru) and PVC/composite planks expand slightly or remain dimensionally stable and are spaced at 1/8 in to 3/16 in using hidden clip fasteners or spacer keys.

Joist spacing (16″ vs 12″ O.C.) and fastener rules

Residential building codes (IRC Section R507) and manufacturer installation instructions link deck board material directly to maximum joist spacing:

  • 16 inches on center: standard for 5/4×6 and 2×6 wood decking laid perpendicular (90°) to the joists, and for most composite planks laid straight.
  • 12 inches on center: required by most composite manufacturers when planks are installed at a 45° diagonal angle across the frame, or on heavy commercial stair landings, to prevent spongy flex between supports.
  • Fastener count: face-screwed wood decking uses two corrosion-resistant #9 or #10 × 2 1/2 in (or 3 in) screws at every joist crossing to prevent cupping. Hidden grooved composite clips use one clip and screw per joist crossing, plus starter clips along the ledger wall.

To lay out exterior deck stairs from the rim joist down to a concrete landing pad, use the stair calculator and check the ledger corners for square with the 3-4-5 right triangle calculator.

Frequently asked questions

How many 5/4×6 deck boards do I need for a 12×16 deck?

If the boards run along the 16 ft dimension and stack across the 12 ft (144 in) width with a 1/8 in gap (5.625 in per row), you need ⌈144 ÷ 5.625⌉ = 26 rows of 16 ft boards (416 net linear feet). Adding a 10% allowance for defects and end trimming brings the order to 29 boards of 16 ft.

What is the actual width of a 5/4×6 or 2×6 deck board?

Both 5/4×6 radius-edge decking and 2×6 dimensional lumber have an actual surfaced width of 5 1/2 inches (5.5 in). A 5/4 board is 1 inch thick (or 1 1/16 in in some hardwood profiles), while a 2×6 is 1 1/2 inches thick.

How many linear feet of 5/4×6 decking cover 100 square feet?

With a 1/8 inch gap between 5 1/2 inch boards, 100 square feet requires 213.3 net linear feet of decking before waste (or about 235 linear feet with 10% waste). If wet pressure-treated boards are laid tight with no gap, 100 sq ft requires 218.2 net linear feet.

How many screws do I need for a deck?

Multiply the number of board rows by the number of joists and multiply by 2 (two screws per board at every joist crossing), then add 10% for dropped or stripped fasteners. A 16×12 ft deck with 26 board rows over 13 joists uses 26 × 13 × 2 = 676 screws (about 744 screws with 10% extra).For hidden clip systems that use one clip per joist crossing, divide the face-screw count by 2.

Should I add more waste for diagonal or picture-frame decking?

Yes. Straight perpendicular decking typically uses a 7% to 10% waste allowance. Diagonal 45° decking generates triangular cutoffs at both ends of every board and requires a 15% waste allowance, plus extra perimeter blocking for picture-frame borders.

How these guides are prepared · Calculations and table values come from the same code as the free tools and are checked by automated tests and against the formulas in the Construction Pro app. Code references are for orientation: confirm requirements with your jurisdiction and your project documents. Found an error? Tell the developer.
Take the next job with you

Keep the calculation with the project.

Use feet-inch fractions, specialty trade tools and saved job calculations in Construction Pro for iPhone and iPad. Free download with in-app Pro options.

View on the App Store ↗

Keep working

Browse all guides