Materials & Takeoff

Concrete Block Calculator: 8×8×16 CMU, Courses & Mortar

Free concrete block and brick calculator. Enter wall length, height and openings to get 8×8×16 CMU block count, horizontal courses, units per course and mortar bags.

Free online tool

Concrete block (CMU) & brick calculator

Estimate concrete masonry blocks or bricks, horizontal courses, units per course and 80-lb mortar bags for a wall.

Total units to order

260 blocks

Base units before waste
247 blocks before 5% waste
Net masonry wall area
219 sq ft net (240 sq ft gross − 21 sq ft openings)
Course layout
12 courses high × 23 units per full course
Estimated 80-lb mortar bags
20 bags (80-lb pre-blended mortar at ~13 blocks/bag)

Net area = 219 sq ft ÷ 0.8889 sq ft per unit = 247 units. With 5% waste = 260 units.

Counts use standard modular masonry coordination with a 3/8 in mortar bed and head joint (an actual 7⅝ × 7⅝ × 15⅝ in CMU covers a 16 × 8 in nominal module, or 1.125 blocks per sq ft). Mortar bag counts are an estimate for bed and head joints only; core-fill grout, bond beams, rebar, corner return blocks and lintels are calculated separately.

Standard 8×8×16 concrete masonry units (CMUs) measure 7 5/8 × 7 5/8 × 15 5/8 inches so that a 3/8 inch mortar joint creates an exact 8 × 16 inch nominal module—requiring 1.125 blocks per square foot (9 blocks per 8 sq ft) and rising one course every 8 inches. Enter wall length, height, opening deductions and unit size above to calculate total blocks or bricks, courses and 80-lb mortar bags.

How concrete block (CMU) wall quantities are calculated

Standard concrete masonry units (CMUs, often called cinder blocks) are manufactured to coordinate with a 3/8 inch mortar joint on an 8-inch modular grid. An 8×8×16 block actually measures 7 5/8 in wide × 7 5/8 in high × 15 5/8 in long (ASTM C90). Once laid with a 3/8 in horizontal bed joint and a 3/8 in vertical head joint, each block occupies a clean 8 in × 16 in nominal face on the wall.

One 8×8×16 block face area = (16 in × 8 in) ÷ 144 = 0.8889 sq ft
Blocks per square foot     = 144 ÷ 128 = 1.125 blocks/sq ft  (9 blocks per 8 sq ft)
Horizontal courses         = Wall height (in) ÷ 8 in
Blocks per full course     = Wall length (in) ÷ 16 in
Total blocks to order      = ⌈Net wall area (sq ft) × 1.125 × (1 + waste %)⌉

For a 30 ft × 8 ft masonry wall (240 sq ft gross) with one 3 ft × 7 ft door opening (21 sq ft deducted, leaving 219 sq ft net), the wall requires ⌈219 × 1.125⌉ = 247 blocks before waste, and 260 blocks with a 5% allowance for cutting and breakage.

8×8×16 concrete block, course and mortar chart by wall size

Every 8 inches of vertical wall height is one course of standard CMU block, so an 8 ft (96 in) wall is 12 courses high and a 10 ft (120 in) wall is 15 courses high. The table below gives the net area, course count, net blocks, order blocks (with 5% waste) and estimated 80-lb pre-blended mortar bags for common foundation and stem-wall sizes.

Standard 8×8×16 CMU block and 80-lb mortar bag counts by wall dimensions
Wall size (less openings)Net areaCourses highNet blocksWith 5% waste80-lb mortar bags
10′ × 4′40 sq ft6 courses45 blocks48 blocks4 bags
20′ × 4′80 sq ft6 courses90 blocks95 blocks8 bags
20′ × 8′160 sq ft12 courses180 blocks189 blocks15 bags
30′ × 8′ (−21 sq ft)219 sq ft12 courses247 blocks260 blocks20 bags
40′ × 8′ (−42 sq ft)278 sq ft12 courses313 blocks329 blocks26 bags
50′ × 8′ (−42 sq ft)358 sq ft12 courses403 blocks424 blocks33 bags
60′ × 10′ (−60 sq ft)540 sq ft15 courses608 blocks639 blocks50 bags

When laying out masonry wall lengths and rough window or door openings on a blueprint, size every horizontal dimension in multiples of 8 inches (half a block) and every vertical height in multiples of 8 inches (one full course). Sticking to the 8-inch modular grid lets masons lay whole and half blocks without wet-sawing custom pieces at every jamb.

Estimating mortar bags versus core-fill concrete grout

Masonry walls use two distinct cementitious products that should never be combined into one line item on an order:

  • Masonry mortar (bed and head joints): bonds the blocks together along the 3/8 in face shells. An 80-lb bag of pre-blended Type N or Type S mortar mix lays approximately 12 to 14 standard 8×8×16 blocks (or roughly 33 to 37 standard modular bricks), depending on joint tooling and waste on the mortar board. Type S mortar is commonly specified for below-grade foundation walls and structural retaining walls, while Type N is common on above-grade non-load-bearing veneers.
  • Core-fill concrete grout (inside the hollow cells): fills the vertical cores that contain rebar dowels and horizontal bond beams. Depending on wall thickness (6 in, 8 in or 12 in CMU) and whether the engineer specifies grouting every cell or only reinforced cells at 24 in to 48 in on center, core grout is ordered separately in cubic yards of coarse masonry grout or bags of core-fill mix.

To calculate the concrete footing strip that supports the block wall, use the concrete calculator and the concrete takeoff worksheet.

Modular brick veneer: courses and bricks per square foot

When you switch the calculator above to Standard modular brick, it uses the modular clay brick size of 3 5/8 in × 2 1/4 in × 7 5/8 in laid with a 3/8 in mortar joint. Three courses of modular brick plus three 3/8 in bed joints equal exactly 8 inches of vertical height, which means three courses of exterior brick veneer align level with every single course of 8×8×16 concrete block backup wall for embedding metal brick ties.

Each modular brick covers 8 in × 2 2/3 in = 21.33 sq in (0.1481 sq ft), which equals exactly 6.75 bricks per square foot of net wall area before waste (or roughly 7.1 bricks per sq ft with 5% waste). Queen, King, Norman and Utility bricks have different face areas, so verify the exact unit dimensions on your brick supplier's data sheet.

Frequently asked questions

How many 8×8×16 concrete blocks are in a square foot?

Exactly 1.125 blocks per square foot (9 blocks for every 8 square feet of wall area). An 8×8×16 block with a 3/8 in mortar joint covers 8 in by 16 in, which is 128 sq in or 0.8889 sq ft.

What are the actual dimensions of an 8×8×16 cinder block?

An 8×8×16 CMU actually measures 7 5/8 in wide × 7 5/8 in high × 15 5/8 in long. It is made 3/8 inch smaller than its nominal 8×8×16 callout on all three axes so that adding a 3/8 inch mortar joint produces an exact 8×8×16 modular grid.

How many blocks will one 80-lb bag of mortar lay?

One 80-lb bag of pre-blended mortar mix typically lays 12 to 14 standard 8×8×16 concrete blocks or 33 to 37 standard modular bricks with a 3/8 in mortar joint. The calculator uses 13 blocks (or 35 bricks) per 80-lb bag as a field planning figure; check the yield printed on your specific mortar bag.

How many courses of block are in an 8 foot wall?

12 courses. Each course of standard 8 in high block (7 5/8 in block plus 3/8 in mortar bed joint) rises 8 inches, so 96 inches ÷ 8 inches = 12 courses.

Does the block count include corner blocks, bond beams or lintels?

The calculator gives the total number of full-size 16×8 face units required for the net wall area. On the order sheet, separate that total into stretchy field blocks, flat-end corner return blocks, bond-beam U-blocks and half-blocks (8×8×8) for flush jamb terminations.

How these guides are prepared · Calculations and table values come from the same code as the free tools and are checked by automated tests and against the formulas in the Construction Pro app. Code references are for orientation: confirm requirements with your jurisdiction and your project documents. Found an error? Tell the developer.
Take the next job with you

Keep the calculation with the project.

Use feet-inch fractions, specialty trade tools and saved job calculations in Construction Pro for iPhone and iPad. Free download with in-app Pro options.

View on the App Store ↗

Keep working

Browse all guides