Divide feet and inches calculator
Split a length into equal parts, count how many pieces of a set length fit, or space pickets and balusters evenly.
Lengths are exact. The result is rounded once, to the nearest 1/16 inch, and every mark is measured from the same end, so rounding does not add up along the length. Enter feet and inches as 11' 7", 11 ft 7 in or 139 (inches), with fractions such as 7 1/2. The tool does not know your tape, your saw or your code: check the kerf of your blade, and check any maximum opening between pickets or balusters with the authority that inspects your project. Calculations run in your browser and are not saved.
To divide feet and inches, turn the length into inches, divide, and turn the answer back into feet and inches. Half of 11′ 7″ is 5′ 9 1/2″; a third is 3′ 10 5/16″, which is on no 1/16 inch mark, so the tool rounds once and measures every mark from the same end to stop the error adding up. It also counts how many pieces of a set length fit with saw kerf and spaces pickets and balusters evenly.
Quick answers: feet divided by 2 to 6
Each answer is the length of one part, rounded to the nearest 1/16 inch. A leading ≈ means the exact answer is not on a 1/16 inch mark. For feet with inches, another number of parts, or the marks for every cut, use the calculator above.
| Length | ÷ 2 | ÷ 3 | ÷ 4 | ÷ 5 | ÷ 6 |
|---|---|---|---|---|---|
| 3′ | 1′ 6″ | 1′ 0″ | 9″ | ≈ 7 3/16″ | 6″ |
| 5′ | 2′ 6″ | 1′ 8″ | 1′ 3″ | 1′ 0″ | 10″ |
| 7′ | 3′ 6″ | 2′ 4″ | 1′ 9″ | ≈ 1′ 4 13/16″ | 1′ 2″ |
| 8′ | 4′ 0″ | 2′ 8″ | 2′ 0″ | ≈ 1′ 7 3/16″ | 1′ 4″ |
| 9′ | 4′ 6″ | 3′ 0″ | 2′ 3″ | ≈ 1′ 9 5/8″ | 1′ 6″ |
| 10′ | 5′ 0″ | 3′ 4″ | 2′ 6″ | 2′ 0″ | 1′ 8″ |
| 11′ | 5′ 6″ | 3′ 8″ | 2′ 9″ | ≈ 2′ 2 3/8″ | 1′ 10″ |
| 12′ | 6′ 0″ | 4′ 0″ | 3′ 0″ | ≈ 2′ 4 13/16″ | 2′ 0″ |
| 14′ | 7′ 0″ | 4′ 8″ | 3′ 6″ | ≈ 2′ 9 5/8″ | 2′ 4″ |
| 16′ | 8′ 0″ | 5′ 4″ | 4′ 0″ | ≈ 3′ 2 3/8″ | 2′ 8″ |
How to divide feet and inches by hand
- Turn the length into inches. Feet × 12 plus the inches. 11′ 7″ is 11 × 12 + 7 = 139 in.
- Divide by the number of parts. 139 ÷ 2 = 69.5 in. For three parts, 139 ÷ 3 = 46.3333 in.
- Turn the answer back into feet and inches. Whole feet are the answer ÷ 12 rounded down, and the rest is inches. 69.5 in is 5 ft with 9 1/2 in left over, so half of 11′ 7″ is 5′ 9 1/2″.
- Turn a decimal inch into a tape fraction. Multiply the decimal part by 16 and round. 46.3333 in has a decimal part of 0.3333, and 0.3333 × 16 = 5.33, so the nearest mark is 5/16 and one third of 11′ 7″ is 3′ 10 5/16″. That reading is 0.0208 in short of the exact length.
Do not divide 11.7 by 2. 11′ 7″ is 11.583 ft, not 11.7 ft, because 7 in is 7 ÷ 12 of a foot. See the decimal to fraction converter if your length is in decimal feet.
Mark every cut without the error adding up
When a length does not divide onto a 1/16 inch mark, the rounded part is a little short or long. If you step that rounded length along the work with a tape or a gauge, the error adds up at every step. Measure each mark from the same end instead: take the exact multiple (1 × the part, 2 × the part and so on) and round that once.
| Mark | Measured from one end (exact multiple, rounded once) | Stepping the rounded part along |
|---|---|---|
| 1 of 3 | 3′ 10 5/16″ | 3′ 10 5/16″ |
| 2 of 3 | 7′ 8 11/16″ | 7′ 8 5/8″ |
| 3 of 3 | 11′ 7″ | 11′ 6 15/16″ |
The last row should land on the far end of the length, 11′ 7″. Stepping the rounded part 3′ 10 5/16″ three times ends 0.0625 in short. Over 3 parts that is small. Over a long run with many parts it is not, and the calculator above lists every mark from one end for this reason.
How many pieces fit in a length, with saw kerf
To find how many pieces of a set length fit, choose the second option in the calculator. Without kerf it is a division, rounded down: 16 ft is 192 in, and 192 ÷ 16 = 12 pieces. Every cut also removes the width of the blade, so n pieces need n × piece length + (n − 1) × kerf. With a 1/8 in kerf the same board gives 11 pieces and 1′ 2 3/4″ left over, because the twelfth piece is short by the kerf of eleven cuts.
| Board and piece | Pieces, no kerf | Pieces, 1/8 in kerf | Left over, 1/8 in kerf |
|---|---|---|---|
| 16′ into 16″ pieces | 12 | 11 | 1′ 2 3/4″ |
| 8′ into 24″ pieces | 4 | 3 | 1′ 11 3/4″ |
| 10′ into 16″ pieces | 7 | 7 | 7 1/4″ |
| 12′ into 18″ pieces | 8 | 7 | 1′ 5 1/4″ |
Kerf is measured on your blade, and a thin-kerf blade removes less than a standard one. The tool also lists where to set the saw line for every cut, measured from one end of the board.
Space pickets and balusters evenly
Items in an opening make one more gap than there are items: gaps at both ends and one between each pair. Every gap is the same, so the gap is the space left after the items, divided by the number of gaps.
Gap = (opening − items × item width) ÷ (items + 1) On-center spacing = gap + item width
Example: six pickets, each 3 1/2 in wide, in an 8 ft (96 in) opening. The space left is 96 − 6 × 3.5 = 75 in, shared by 7 gaps, so each gap is 10.7143 in, about 10 11/16″. The pickets are 1′ 2 3/16″ on center.
| Item | Left edge | Right edge |
|---|---|---|
| Picket 1 | 10 11/16″ | 1′ 2 3/16″ |
| Picket 2 | 2′ 0 15/16″ | 2′ 4 7/16″ |
| Picket 3 | 3′ 3 1/8″ | 3′ 6 5/8″ |
| Picket 4 | 4′ 5 3/8″ | 4′ 8 7/8″ |
| Picket 5 | 5′ 7 9/16″ | 5′ 11 1/16″ |
| Picket 6 | 6′ 9 13/16″ | 7′ 1 5/16″ |
Measure every position from the same end and mark the left edge of each picket, instead of stepping a spacer along the rail. If a picket sits tight against each end post, use the number of items minus one for the number of gaps. The calculator does not decide the largest gap your code allows; check that with the authority that inspects your project.
Equal stair risers are the same kind of division: the total rise divided by the number of risers. The stair rise and run chart does it for total rises from 12 to 120 in.
Mistakes that put the marks out
- Treating inches as decimal feet. 11′ 7″ is 11.583 ft. Divide in inches, or convert first.
- Stepping the rounded length along the work. Measure every mark from the same end.
- Forgetting the kerf. Equal pieces cut one after another from a board each lose a blade width, so the last piece comes out short.
- Counting items instead of gaps. N items in an opening have N + 1 gaps; if the first and last items sit against the ends, they have N − 1.
- Rounding the gap and leaving the difference at the end. A rounded gap repeated across the opening ends with an uneven last gap. Mark each position from the exact values.
Frequently asked questions
What is 11 feet 7 inches divided by 2?
11′ 7″ is 139 in. 139 ÷ 2 = 69.5 in, which is 5′ 9 1/2″. Half of 11′ 7″ is 5′ 9 1/2″.
How do I divide feet and inches?
Turn the length into inches (feet × 12 + inches), divide by the number of parts, then turn the answer back into feet and inches and a 1/16 inch fraction. Dividing in inches avoids the mistake of treating 11′ 7″ as 11.7 ft.
How many 16 inch pieces are in 16 feet?
16 ft is 192 in, and 192 ÷ 16 = 12 pieces if nothing is lost to saw kerf. With a 1/8 in kerf, 11 pieces fit and 1′ 2 3/4″ is left over.
How do I divide a length into equal parts with a tape measure?
Mark each point from the same end. For 11′ 7″ in 3 parts, the marks are 3′ 10 5/16″ and 7′ 8 11/16″ from one end. Each is the exact multiple of one third of the length, rounded once to 1/16 inch.
How do I space pickets or balusters evenly?
Subtract the total width of the items from the opening, then divide by the number of items plus one. That is the gap at every position, including both ends. Add the item width to the gap for the on-center spacing.
Can I divide a length by another length?
Yes. Choose "Count the pieces of a set length that fit". It divides the length by the piece length, rounds down to whole pieces and, if you enter a saw kerf, takes the blade width into account.